How to Replace the Replacement Key Battery For the Saab 9-3
Saab owners have a unique procedure to add a second key. It requires dealer support using the handheld computer known as Tech-2. A new key and transponder need to be bought and then programmed to the car.
Rotate your keys to prevent one from wearing out quicker than another. This will also help to keep your keys in good condition.
Replacement Case
The new key fobs for keys are not like the older Saab keys. They're equipped with electronic devices that make them difficult to duplicate. This has made theft of cars much more difficult than it was twenty years ago. However, it also has made the replacement of lost keys a more costly endeavor.
Saab 9-3 owners must have two keys working. It is costly to replace a lost key because it requires replacing the CIM module, and reprogramming the locking cylinders. Dealers usually charge between $100 and $200 for this.
There are saab keys replacement to cut down on the high cost. Some parts providers can look up the code from an old key (usually the same one that opens the doors and turns the ignition) and cut a brand new metal key blade for just a fraction of dealer cost. The key, however, must be the same as the original to work correctly in your car.
Follow these steps to replace the case. You'll need an flathead screwdriver and patience. Utilizing the screwdriver, slowly pry the plastic apart and separate the emergency keys from the case. Once the case is open, remove the electronic components and put them in your new case. Make sure you insert the correct badge and key back into the case as well.
Replacement Battery
The Saab 9-3 replacement battery is a low-cost component that can be quickly and easily replaced. The YouTube video of Cyclone Cyd demonstrates the procedure for replacing the battery of the remote fob with just four steps. This tutorial can be used for any modern saab key fob though the process may vary slightly.
The first step is to find the button that lets off the backup key on the fob. It's usually just below the Saab logo on the back of the fob. Next use a flathead screwdriver into the small hole in this button. This should be enough to open the case of the fob to allow you to replace the battery.
Once you have installed the new batteries CR1632, you can reassemble the remote key fob. You can then program it into your car. The entire process should not be more than an hour. It is a very simple procedure that doesn't require any special equipment.
The process is more complicated if you've lost the key, but it's possible. The dealer must first read the VIN of the vehicle, and then purchase an additional TWICE module and key blade that has the correct unique code. The dealer will then need to program the key using MDI which is a new software tool.
Replacement Key Fob
The key fob has a battery that is used to lock and unlock your vehicle. The batteries last for a certain time and eventually fail. This is a typical issue that affects all cars, and the good news is that you can change the batteries in most key fobs without replacing the whole case. Amazon sells replacement fobs that have all the electronics in place. You can simply open the case and replace the batteries. It is important to note that you'll have to take out the emergency key first. you can do this by putting the screwdriver of a small flathead into the slot that is located in the middle of the case. The case should split when you move the screwdriver around it.
If you are about to replace the keys, ensure you have a spare, since this will cut down the total cost by a substantial amount. If you have an additional key, you can request the dealer to cut it and program it to your vehicle. This is a lot less expensive than purchasing a new fob.
If you don't have a spare car key, you can add an additional key to your car, however it requires a lot of research and effort. The cost of adding a second key is around a hundred dollars and it also requires the programming of the car's computer. This can be done by a professional, however it's a costly choice for the majority of owners.
Replacement Ignition
In contrast to earlier Saab cars, the modern SAAB 9-3 models are equipped with an upgraded alarm system that is based on a coded key. This means that should you lose only one working key, acquiring another one could be very costly since the car needs to have a unique computer module added and it also must be specially designed to accept a different key. Even a dealer can charge hundreds of dollars to program a new key even if they're unable to complete the task.
Dealers will charge you the highest price to replace your car's computer (also known as the CIM or SAAB twice) in the event that you lose your only functioning key. Instead we can reprogramme the EEPROM in your current car computer to prepare it for a replacement key, slashing over 50% of the amount you spend at a dealer.
If you have owned a SAAB 9-3 for a long time you're aware that the ignition keys aren't very durable. If your ignition key isn't functioning properly, you must consider replacing it. They can become extremely sticky and the buttons can fall off. It's not as difficult as it seems to replace the ignition key. With the appropriate tools, it could be accomplished in a matter of minutes.